|
Wavelength-tunable lasers are highly desired to achieve dynamically reconfigurable optical networks and significantly reduce the number of redundant lasers required in optical communication inventories.1, 2, 3, 4 Tunable fiber lasers are among the most promising sources due to their high energy conversion efficiency , large gain bandwidth across C and L bands, and inherent compatibility with optical fibers, which leads to extremely low insertion loss and reduced packing cost.3 However, most of the existing tunable laser technologies involve moving mechanical parts,4, 5, 6, 7, 8, 9 which not only requires precise mechanical moving control elements, but also increases device size and weight and generates reliability issues. In this paper, we present a thermo-optically tunable fiber ring laser without involving any moving mechanical parts. The laser is based on a polymer-spaced Fabry-Pérot (F-P) étalon with a short cavity length of and an ultra-low polarization-dependent loss (PDL) of . A wavelength tuning range of and a wavelength stability of have been demonstrated. Such a fiber laser provides a compact device structure and allows easy device packaging due to the ultra-low PDL of the wavelength tuning element. The schematic diagram of the thermo-optically tunable fiber laser is shown in Fig. 1. It consists of a wavelength division multiplexing coupler (WDM ), a 3-m-long erbium doped fiber (EDF; OFS HG980), two isolators, a polymer-filled F-P étalon and a 5% output tap coupler. The total length of the fiber ring cavity is 5 meters, which gives a longitudinal mode separation of . The polymer-filled F-P étalon functions as a thermo-optically tunable optical filter, which selects the lasing wavelength of the fiber laser. It was constructed by filling polymers into an air-spaced F-P étalon. The cross section and the cavity length of the air-spaced F-P étalon are and , respectively. The polymer fill inside the F-P étalon is Norland optical adhesive 61 (NOA61), which has a refractive index of 1.541 at the wavelength of at room temperature . The finesse of the polymer-filled F-P cavity was measured to be approximately 100. The F-P étalon has a free-spectral range (FSR) of and a 3-dB bandwidth of , which indicates that there are approximately 100 longitudinal modes in each pass band of the F-P filter. The polymer-spaced F-P étalon was packaged with polarization maintenance (PM)–fiber pigtailed collimators on both the input and the output sides. The focal length and the aperture of the PM-fiber pigtailed collimators are and , respectively. Due to this ultra-low PDL, no special attention was paid to aligning the polarization orientation of the FP filter to the fiber laser. The insertion loss (IL) and PDL of the F-P filter were measured to be and , respectively. The resonant wavelength of the F-P étalon is given by: where is the refractive index (1.541 at room temperature at the wavelength of ), is the cavity length, is an integer, and is the optical path length . The temperature dependence of the optical path length10 is given by:where is the coefficient of thermal expansion (CTE), for NOA61, and is the thermo-optic coefficient, which is for NOA61.11 The resonant wavelength can thus be tuned by changing the refractive index or the cavity length , or both. The wavelength tuning range (the shift of the resonant wavelength ) can be written as:As indicated in Eq. 3, by controlling the temperature, a thermo-optically tunable optical filter can be achieved. This tunable optical fiber functions as a wavelength selection element for the fiber laser.The wavelength tuning spectrums of the fiber ring laser at different temperatures were characterized using an optical spectrum analyzer (Agilent 86140B), as shown in Fig. 2. As indicated in Fig. 2, the wavelength of the fiber ring laser can be continuously tuned from to when the temperature of the F-P étalon was increased from to . A side-mode suppression ratio (SMSR) over was obtained. Figure 3 shows the measured wavelength tuning ranges at different temperatures. The solid trace is the calculated wavelength tuning range as a function of temperature. Note that the measured wavelength tuning ranges are smaller than calculation results. One possible reason for this is because the F-P cavity is mounted on a thermal-electric cooler (TEC), which has a much smaller coefficient of thermal expansion. This would limit the expansion of the polymer materials and result in smaller wavelength tuning ranges than expected values. To obtain high wavelength stability, the temperature of the thermo-optic filter was controlled by a temperature controller. The close-loop gain and time constant were optimized to achieve an excellent temperature stability of . The wavelength tuning speed was approximately . By reducing the thermal capacitance of the polymer-filled F-P étalon, e.g., decreasing the size and increasing the thermal conductivity of the F-P étalon, faster wavelength-tuning speed (tens of ms) can be expected. The power consumption of the polymer-spaced F-P filter at was measured to be . The wavelength stability at each temperature was measured to be . The wavelength instability is not due to the temperature fluctuation . We believe that it is the result of the mode-hopping and competing of multilongitudinal modes within the passband of the F-P étalon as well as volume relaxation of polymer materials.12 By increasing the finesse of the F-P étalon, the number of the longitudinal modes within the passband of the F-P cavity can be reduced, and a higher wavelength stability can be expected. In summary, we present a thermo-optically tunable fiber ring laser with high wavelength stability. The laser yields a wavelength tuning range of without any moving mechanical parts. A wavelength stability of and a SMSR of over were obtained. By increasing the finesse of the F-P cavity, a higher wavelength stability can be expected. Such a fiber laser provides a compact structure by eliminating the mechanical moving parts. In addition, the ultra-low PDL of the wavelength tuning element allows easy device alignment and packaging. ReferencesJ. P. Rayn,
“WDM North American development trends,”
IEEE Commun. Mag., 36
(2), 40
–44
(1998). 0148-9615 Google Scholar
C. Vazquez,
S. Vargas,
J. M. S. Pena, and
P. Corredera,
“Tunable optical filters using compound ring resonators for DWDM,”
IEEE Photonics Technol. Lett., 15 1085
–1087
(2003). https://doi.org/10.1109/LPT.2003.815328 1041-1135 Google Scholar
X. Dong,
P. Shum,
N. Q. Ngo,
H.-Y. Tam, and
X. Dong,
“Output power characteristics of tunable erbium-doped fiber ring lasers,”
J. Lightwave Technol., 23 1334
–1341
(2005). 0733-8724 Google Scholar
Y. Hibino,
“Recent advances in high-density and large-scale AWG multi/demultiplexers with higher index-contrast silica-based PLCs,”
IEEE J. Sel. Top. Quantum Electron., 8 1090
(2002). https://doi.org/10.1109/JSTQE.2002.805965 1077-260X Google Scholar
J. Stone and
L. W. Stulz,
“Pigtailed high finesse tunable FP interferometer with large, medium, and small FSR,”
Electron. Lett., 23 781
–783
(1987). 0013-5194 Google Scholar
J. L. Jackel,
J. E. Baran,
A. d’ Alessandro, and
D. A. Smith,
“A passband-flattened acousto-optic filter,”
IEEE Photonics Technol. Lett., 7 318
(1999). https://doi.org/10.1109/68.372758 1041-1135 Google Scholar
J. Y. Liu and
K. M. Johnson,
“Analog smectic ferroelectric liquid crystal Fabry Perot optical tunable filter,”
IEEE Photonics Technol. Lett., 7 1309
(1995). https://doi.org/10.1109/68.473481 1041-1135 Google Scholar
E. L. Wooten,
R. L. Stone,
E. W. Miles, and
E. M. Bradley,
“Rapidly tunable narrowband wavelength filter using unbalanced Mach-Zehnder interferometers,”
J. Lightwave Technol., 14 2530
–2536
(1996). https://doi.org/10.1109/50.548151 0733-8724 Google Scholar
A. Locco,
H. G. Limberger, and
R. P. Salathe,
“Bragg grating fast tunable filter,”
Electron. Lett., 33 2147
–2148
(1997). https://doi.org/10.1049/el:19971466 0013-5194 Google Scholar
Y. Kokubua,
N. Funato, and
M. Takizawa,
“Athermal waveguide for temperature-independent lightwave devices,”
IEEE Photonics Technol. Lett., 5 1297
–1300
(1993). https://doi.org/10.1109/68.250049 1041-1135 Google Scholar
X. Wang,
B. Howley,
M. Y. Chen, and
R. Chen,
“Crosstalk-minimized polymeric switch,”
IEEE Photonics Technol. Lett., 18 16
–18
(2006). 1041-1135 Google Scholar
|