The cadmium zinc telluride imager (CZTI) on board AstroSat consists of an array of a large number of pixelated cadmium zinc telluride (CZT) detectors capable of measuring the polarization of incident hard x-rays. The polarization measurement capability of CZTI for on-axis sources was experimentally confirmed before the launch. CZTI has yielded tantalizing results on the x-ray polarization of the Crab nebula and pulsar in the energy range of 100 to 380 keV. CZTI has also contributed to the measurement of prompt emission polarization for several gamma-ray bursts (GRBs). However, polarization measurements of off-axis sources such as GRBs are challenging. It is vital to experimentally calibrate the CZTI sensitivity to off-axis sources to enhance the credence of the measurements. In this context, we report the verification of the off-axis polarimetric capability of pixelated CZT detectors through controlled experiments carried out with a CZT detector similar to that used in CZTI and extensive Geant4 simulations of the experimental setup. Our current results show that the CZT detectors can be used to measure the polarization of bright GRBs with off-axis angles of up to ∼60 deg. However, at incidence angles between 45 deg and 60 deg, there might be some systematic effects that need to be taken into account when interpreting the measured polarization fraction.
As a Near- IR instrument to PRL's upcoming 2.5 m telescope, NISP is designed indigeniously at PRL to serve as a multifaceted instrument. Optical, Mechanical and Electronics subsystems are being designed and developed in-house at PRL. It will consist of imaging, spectroscopy and imaging-polarimetry mode in the wavelength bands Y, J, H, Ks i.e. 0.8 - 2.5 µm. The detector is an 2K x 2K H2RG (MCT) array detector from Teledyne, which will give a large FOV of 10' x 10' in the imaging mode. Spectroscopic modes with resolving power of R ~ 3000, will be achieved using grisms. Spectroscopy will be available in single order and a cross-dispersed mode shall be planned for simultaneous spectra. The instrument enables multi-wavelength imaging- polarimetry using Wedged-Double Wollaston (WeDoWo) prisms to get single shot Stokes parameters (I, Q, U) for linear polarisation simultaneously, thus increasing the efficiency of polarisation measurements and reducing observation time.
NISP, a multifaceted near-infrared instrument for the upcoming 2.5m IR telescope at MIRO Gurushikhar, Mount Abu, Rajasthan, India is being developed at PRL, Ahmedabad. NISP will have wide (FOV = 10’ x 10’) field imaging, moderate (R=3000) spectroscopy and imaging polarimetry operating modes. It is designed based on 0.8 to 2.5μm sensitive, 2048 X 2048 HgCdTe (MCT) array detector from Teledyne. Optical, Mechanical and Electronics subsystems are being designed and developed in-house at PRL. HAWAII-2RG (H2RG) detector will be mounted along with controlling SIDECAR ASIC inside LN2 filled cryogenic cooled Dewar. FPGA based controller for H2RG and ASIC will be mounted outside the Dewar at room temperature. Smart stepper motors will facilitate motion of filter wheels and optical components to realize different operating modes. Detector and ASIC temperatures are servo controlled using Lakeshore’s Temperature Controller (TC) 336. Also, several cryogenic temperatures will be monitored by TC for health checking of the instrument. Detector, Motion and Temperature controllers onboard telescope will be interfaced to USB Hub and fiber-optic trans-receiver. Remote Host computer interface to remote end trans-receiver will be equipped with in-house developed GUI software to control all functionalities of NISP. Design and development aspects of NISP Electronics will be presented in this conference.
Near-infrared Imager Spectrometer and Polarimeter (NISP) is a camera, an intermediate resolution spectrograph and an imaging polarimeter being developed for upcoming 2.5m telescope of Physical Research Laboratory at Mount Abu, India. NISP is designed to work in the Near-IR (0.8-2.5 micron) using a H2RG detector. Collimator and camera lenses would transfer the image from the focal plane of the telescope to the detector plane. The entire optics, mechanical support structures, detector-SIDECAR assembly will be cooled to cryo-temperatures using an open cycle Liquid Nitrogen tank inside a vacuum Dewar. GFRP support structures would be used to isolate cryogenic system from the Dewar. Two layer thermal shielding would be used to reduce the radiative heat transfer. Molecular sieve (getter) would be used to enhance the vacuum level inside Dewar. Magnet-reedswitch combination are used for absolute positioning of filterwheels. Here we describe the mechanical aspects in detail.
We explore the use of scintillation detectors coupled with silicon photomultipliers (SiPMs) as position sensitive hard x-ray spectroscopic detectors for potential applications in the field of high-energy astrophysics. X-ray photons on interaction with scintillation crystals generate optical photons and the distribution of these scintillation light photons is captured with the array of SiPM pixels, providing the spectral and spatial information of the incident x-ray photons. As the position is estimated by fitting the distribution of optical photons, it should be possible to achieve spatial resolution lesser than the pixel size. Development of two detector modules with CsI (Tl) and CeBr3 scintillators coupled with different sets of array of SiPM pixels is presented here. Spectral and spatial resolutions of both detector modules are characterized with experiments using x-ray lines from laboratory radioactive sources. It is shown that a faster scintillator with an array of low-noise SiPM pixels provides better spectral and spatial resolution and it is possible to achieve subpixel spatial resolution with such a detector module.
There is growing interest in high-energy astrophysics community for the development of sensitive instruments in the hard X-ray energy extending to few hundred keV. This requires position sensitive detector modules with high efficiency in the hard X-ray energy range. Here, we present development of a detector module, which consists of 25 mm x 25 mm CeBr3 scintillation detector, read out by a custom designed two dimensional array of Silicon Photo-Multipliers (SiPM). Readout of common cathode of SiPMs provides the spectral measurement whereas the readout of individual SiPM anodes provides measurement of interaction position in the crystal. Preliminary results for spectral and position measurements with the detector module are presented here.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.