The Habitable Exoplanet Observatory Mission (HabEx) is one of four missions under study for the 2020 Astrophysics Decadal Survey. Its goal is to directly image and spectroscopically characterize planets in the habitable zone around nearby sun-like stars. Additionally, HabEx will perform a broad range of general astrophysics science enabled by 115 to 1700 nm spectral range and 3x3 arc-minute FOV instruments. Critical to achieving its science goals is a large, ultra-stable UV/Optical/Near-IR (UVOIR) telescope. The baseline HabEx telescope is a 4-meter off-axis unobscured three-mirroranastigmatic, diffraction limited at 400 nm with wavefront stability on the order of a few 10s of picometers. This paper summarizes the opto-mechanical design of the HabEx baseline optical telescope assembly, including a discussion of how science requirements drive the telescope’s specifications, and presents analysis that the baseline telescope structure meets its specified tolerances.
The Habitable-Zone Exoplanet Observatory Mission (HabEx) is one of four large missions under review for the 2020 astrophysics decadal survey. Its goal is to directly image and spectroscopically characterize planetary systems in the habitable zone around nearby Sun-like stars. In addition, HabEx will perform a broad range of general astrophysics science enabled by a 115- to 1700-nm spectral range and 3 × 3 arcminute field of view. Critical to achieving its science goals, HabEx requires a large, ultrastable UV/optical/near-IR telescope. Using science-driven systems engineering, HabEx specified its baseline telescope to be a 4-m off-axis, unobscured three-mirror anastigmatic architecture with diffraction-limited performance at 400 nm, and wavefront stability on the order of a few tens of picometers. We summarize the systems-engineering approach to the baseline telescope assembly’s optomechanical design, including a discussion of how science requirements drive the telescope’s specifications. We also present structural thermal optical performance analysis showing that the baseline telescope structure meets its specified tolerances. We report new and updated analysis that is not in the HabEx final report.
The proposed Habitable Exoplanet (HabEx) astrophysics facility is one of four large such facilities being proposed to the 2020 decadal. It is a large telescope that is sensitive to ultraviolet, optical, and near-infrared photons. The proposed design’s overall length is on the order of 17.2 m and its maximum cross section is on the order of 5.25 × 5.25 m. The primary mirror is 4 m in diameter. A transient dynamic analysis was performed to estimate the order of magnitude of ring down time after moving the telescope and pointing at a new target for science planning purposes. Without uncertainty factors, results from a simple re-pointing maneuver indicate that primary to secondary mirror LOS errors are on the order of 10-4 pico-m after 5 minutes. Also, a frequency response analysis was performed to predict the impact of planned micro-thruster vibrations on required stability. Based on provided noise level associated with the micro-thrusters and loading assumptions and without uncertainty factors, the assessed vibrations do not impact predicted performance requirements.
The Habitable Exoplanet Observatory Mission (HabEx) is one of four missions under study for the 2020 Astrophysics Decadal Survey. Its goal is to directly image and spectroscopically characterize planetary systems in the habitable zone around nearby sun-like stars. Additionally, HabEx will perform a broad range of general astrophysics science enabled by 100 to 2500 nm spectral range and 3 × 3 arc-minute FOV. Critical to achieving its the HabEx science goals is a large, ultrastable UV/Optical/Near-IR (UVOIR) telescope. The baseline HabEx telescope is a 4-meter off-axis unobscured threemirror- anastigmatic, diffraction limited at 400 nm with wavefront stability on the order of a few 10s of picometers. This paper summarizes the opto-mechanical design of the HabEx baseline optical telescope assembly, including a discussion of how science requirements drive the telescope’s specifications, and presents analysis that the baseline telescope structure meets its specified tolerances.
The Advanced Mirror Technology Development (AMTD) project is in Phase 2 of a multiyear effort initiated in Fiscal Year 2012 to mature toward the next technology readiness level critical technologies required to enable 4-m-or-larger monolithic or segmented ultraviolet, optical, and infrared (UVOIR) space telescope primarymirror assemblies for general astrophysics and ultra-high-contrast observations of exoplanets. As part of AMTD II, a free-free modal test was performed of a light weighted slumped 1.5 m mirror made of Corning Ultra Low Expansion (ULE®) material. The test article and support structure were suspended via bungee to simulate a free-free environment. Modes were excited by roaming an instrumented modal test hammer and responses were measured. Predicted and measured frequencies are presented as well as Modal Assurance Criteria (MAC) results to compare the mode shapes. The finite element mirror model used for pre-test predictions and posttest comparisons was provided by the mirror vendor, Harris Corporation. The mirror FEM included deformations of the ribs that were a result of the slumping process. Modal test frequencies matched predictions within the 5% target with the exception of one mode and that pair differed by 5.2%. Of the seven modes measured and predicted, four had MAC values meeting the target of ≥ 0.90, one was just under and two were notably below the target.
Lynx, formerly known as the X-Ray surveyor, is one of the large strategic mission concepts being studied for input into the 2020 Astrophysics Decadal Survey. Lynx is the first future X-ray mission concept planning to match Chandra’s angular-resolution and will combine this with very high throughput, large field of view, and high-resolution spectroscopy for point-like and extended sources. These ambitious performance requirements clearly merit early detailed engineering to demonstrate feasibility. An on-going structural dynamic analysis is being performed on the Lynx structural design to predict dynamic responses, jitter, to expected on-board vibrational disturbances. Applicable disturbance sources include a cryogenic pump, and six reaction wheels. The structural design, disturbances, analysis, and results are presented. Ultimately, responses will be compared to Lynx performance requirements as they relate to a system error budget.
One of the driving structural requirements of the Habitable Exo-Planet (HabEx) telescope is to maintain Line Of Sight (LOS) stability between the Primary Mirror (PM) and Secondary Mirror (SM) of ≤ 5 milli-arc seconds (mas). Dynamic analyses of two configurations of a proposed HabEx 4 meter off-axis telescope structure were performed to predict effects of a vibration input on primary/secondary mirror alignment. The dynamic disturbance used as the forcing function was the James Webb Space Telescope reaction wheel assembly vibration emission specification level. The objective of these analyses was to predict “order-of-magnitude” performance for various structural configurations which contribute to efforts in defining the HabEx structural design’s global architecture. Two variations of the basic architectural design were analyzed. Relative motion between the PM and the SM for each design configuration are reported.
KEYWORDS: Mirrors, Space operations, Finite element methods, Space telescopes, Data modeling, James Webb Space Telescope, Structural design, Structural dynamics, Interfaces, Space mirrors
Analytical tools and processes are being developed at NASA Marshal Space Flight Center in support of the Advanced Mirror Technology Development (AMTD) project. One facet of optical performance is mechanical stability with respect to structural dynamics. Pertinent parameters are: (1) the spacecraft structural design, (2) the mechanical disturbances on-board the spacecraft (sources of vibratory/transient motion such as reaction wheels), (3) the vibration isolation systems (invariably required to meet future science needs), and (4) the dynamic characteristics of the optical system itself. With stability requirements of future large aperture space telescopes being in the lower Pico meter regime, it is paramount that all sources of mechanical excitation be considered in both feasibility studies and detailed analyses. The primary objective of this paper is to lay out a path to perform feasibility studies of future large aperture space telescope projects which require extreme stability. To get to that end, a high level overview of a structural dynamic analysis process to assess an integrated spacecraft and optical system is included.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.