KEYWORDS: Radiation effects, Beryllium, 3D modeling, Scanning electron microscopy, Radiation oncology, Radiotherapy, Particles, Metals, Medicine, Medical research
Radiation research primarily aims to improve radiation therapy and the use of radiation on soft materials. There are many reports available on the effects of high-dose radiation on cells, but the effects of low-dose radiation still require much scientific evidence. Therefore, we intend to study the effects of low-dose irradiation on cell internal structures by cold cathode field emission carbon nanotube (CNT)-based cell irradiator. Hence, we designed a CNT-based microbeam system to irradiate cells. CNT emitter was fabricated by synthesizing CNTs on point shaped substrate. The growth of CNTs was confirmed by scanning electron microscope (SEM). The aging process was carried out to improve the performance of the CNT emitter and the I-V characteristic was measured. We also conducted the simulation study in order to confirm the electric field change and the electron beam trajectory.
We developed a compact vacuum X-ray tube using an alumina body instead of glass. A filament is implanted as a cathode which follows Richardson-Dushman equation. After aging the filament to eliminate impurities on the filament which improves performance of filament before tubing, tube current was obtained from anode voltage of 6kV, 3mA to 40kV, 3.15mA. The pulse high voltage generator is designed and developed to make the tube less stressful. With the ceramic X-ray tube, X-ray images of human breast and teeth phantom were successfully obtained, verifying the potential of the compact alumina vacuum sealed X-ray tube in X-ray application for medical imaging.
We designed and developed the vacuum sealed x-ray tube based on carbon nanotube(CNT) field emitter for mobile medical x-ray devices and also design the test bed for CNT x-ray tube. The CNT was synthesized by chemical vapor deposition(CVD) method on a metal alloy substrate. The grown CNT is assembled with a gate and a focuser and then combined into an electron gun(e-gun) through a brazing process. The the e-gun had an aging process inside the vacuum chamber. As a result of aging, the CNT e-gun was able to generate anode current of 1.5 mA at electric field of about 4 V/μm, and field emission current was also stabilized. After the aging process, the e-gun was brazed into a ceramic X-ray tube inside a high-temperature furnace at a vacuum degree of E-06 torr and vacuum sealed. Field emission characteristic was measured using this X-ray tube and compared with an e-gun, and almost similar results were obtained. Incase of Xray tube, we applied a higher electric field while controlling the current at 500ms intervals through pulse driving. As a result, X-ray images of human teeth were successfully acquired using CNT X-ray tubes.
A microfocus X-ray source based on carbon nanotube (CNT) emitter grown by chemical vapor deposition is presented in this paper. The microfocus X-ray source is developed for the intraoperative specimen radiographic system, which can be used inside the operation theatre and helps reducing the surgery time during breast conserving surgery by confirming the extent of margin on specimen. This high focusing X-ray source is realized by growing CNTs on pointed structures. The field emission characteristic shows that maximum anode current of 1mA, which corresponds to a maximum emission current density of 500 mA/cm2 from the CNT-based point emitter. The optimized parameter for the assembly of electron gun was achieved by using commercially available CST simulation software. Consequently, this microfocus X-ray tube could produce X-ray image of multilayer printed circuit board showing fine lines of integrated circuit.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.