Fabrication of single-mode fiber coupler has widely expands. However, directional fiber coupler
geometry always affects the power propagation either two or three ports. This paper describes
power launching by NX3 single mode fiber, examined using a matrix transfer for linear and
triangle order, calculated from the eigenvalue and the eigenvector. This eigenvalue is referred to
the coupling coefficient, where it can be expressed as an effective power transmitted to another
fiber. The ratio of coupling coefficient between adjacent axial fibers varies, which can be
achieved by adjusting separation of fiber and refractive index of core and cladding. A calculation
has been shown in 3D that both power transmission and phase are affected by not only the
geometry order, but also the variation of coupling coefficient, assuming the propagation
constants, cross section, and separation of coupling length fiber axis are held constant. This
calculation can be applied for any sources of wavelength and junction.
This paper describes the breakdown voltage of SiO2 fiber using Pockel's effect and empirical equation. The model is
evaluated by coupling coefficient and refractive index changes. A 1x2 single-mode directional coupler switch has been fabricated. A large electro-optic effect causes a change in the optical properties when a slowly varying electric field is applied. A model to describe the breakdown voltage for driving the optical switch of the fusion SiO2 fiber coupler has been developed. A voltage is applied through sectioned electrodes along the coupling length. This model uses the coupling coefficient and the changes in the refractive index to describe the optical switching. The change of refractive index due to the linear electro-optic Pockel effect and an empirical equation are used to calculate the value of coupling
coefficient. The result shows that the changes of the refractive index increases exponentially as a function of separation
fiber axis from 5 to 8 μm. The breakdown voltage and refractive indices difference depict a linear relationship. The increment of coupling coefficient shows that the value of voltage is reduced.
This paper describes a new model for the breakdown voltage of SiO2 fiber coupler using the Pockel effect and empirical
equation. The model is evaluated by using the coupling coefficient and the changes in the refractive index. We found that
the breakdown voltage is in the order of 102 volt correspond to coupling coefficient by the order of mm-1. Increasing the
value of coupling coefficient between the electrodes leads to a reduction in the breakdown voltage.
Coupled 1X2 Single Mode Fiber (SMF-28e"R") has been successfully fabricated using a slightly unstable torch flame at a
temperature range of 800°C to 1350°C injecting hydrogen gas flowing at pressure of 1 bar. The coupling ratio and
coupling coefficient can be examined from 1% until 75%. In this paper, we compare the experimental results by using a
simple kinetic model of coupling coefficient where internal and external parametric functions are considered. This
equation is time independent and is then integrated over the direction of the coupling ratio range for various separation
fibers axis between two cores. The result shows that the separation between the cores significantly affects coupling
coefficient exhibiting exponential behavior. In the experiment the coupling coefficient gradient is significantly changed
towards the coupling ratio but in modeling it has a function of separation fiber axis and no power imposed. These
phenomena will determine the effects of power losses at coupling region where fabrications of coupled fibers are
demonstrated.
In this paper we present theoretical and experimental analysis on Nd:YAG laser microwelding for pigtailing laser diode
transmitter through two ball lenses that are employed for effectively matching the elliptical mode field of the laser diode
with the circular on of the single mode fiber. The fiber attachment and the fixing of various coupling components have
been performed in what is so called active alignment process. The system continues measuring the coupled power during
the processes of alignment and attachment of various coupling components as well as the working distance and
misalignment tolerances optimizations. Results of theoretical modeling of laser weld penetration depth agree with the
experimentally measured results in the low laser pulse energy range. Moreover the laser pulse parameters such as,
duration, energy, number of pulse shoots as well as the focusing position over the workpiece and angle of laser pulse
incidence are found to have very significant effects on the weld yields and greatly affect the laser weld depth to width
ratio. Optimization of all the mentioned parameters found to be necessary for achieving strong laser microwelds with
more penetration and less width in the attachments of the sensitive optical components inside the packaged photonic devices modules.
In this paper we present analysis on three different coupling systems, i.e., butt, single ball lens, and two ball lenses
between the tips of two coupled single mode fiber in semiconductor optical amplifier (SOA) module. The coupling
components inside the module can be aligned in an active alignment process and attached by means of dual beam from
an Nd: YAG laser welding system. The tips of the coupled fiber are ferruled inside metallic tubes to enable the
attachment to the substrates through saddle-shaped welding clips. Investigations of the variations of coupling efficiency
with the with working distance for the three schemes showed that two ball lenses is more efficient with coupling
efficiency of 75% followed by single ball lens at 55% and butt coupling mode at 20% maximum. In addition dual ball
lens configuration have shown to have better longitudinal tolerant even with an elliptical beam profile from the source
fiber. This is however not the case in single ball lens and butt coupling scheme. We also observe however the optimum
separation between the two lenses at in the range between 0.35 mm - 0.45 mm. This is to ensure the coupling efficiency
is the highest possible within the acceptable tolerant misalignments.
Fiber couplers are widely used in telecommunication and industry as a passive splitting power device. The effective
power coupling and transmitting from one fiber to another is mainly determined by both coupling length and coupling
coefficient. Coupling length can be calculated directly but for coupling coefficient it depends upon the refractive index
and separation fiber axis. After fusion processes of two SMF-28e(R) couplers, the refractive index is unknown due to
change in the radius of fiber (rcladd<40μm and rcore<1.5μm). Coupling coefficient range is obtained from a distribution of
coupling ratio and compared with the empirical formula which also enables to calculate refractive index. In this
experiment, coupling coefficient in the range of 0.6-0.9/mm is calculated as a function of separation fiber axis and
refractive index of core and cladding. The result shows a good correlation between experimental results and theoretical
calculation.
This paper presents some analysis for the matching between the elliptical mode field of 1550nm high power laser diode with
the circular mode field of the single mode fiber in order to obtain high coupling efficiency with relaxed misalignment
tolerances. Three coupling schemes namely Butt, single ball lens and double ball lenses coupling schemes have been
employed in pigtailing the butterfly laser diode module using laser welding technique with dual beams from Nd:YAG laser
welding system for the attachment of coupling components. The process of fiber attachment to laser diode and welding of
various coupling components, such as lens holders, fiber ferrule and welding clips have been performed in what is so called
active alignment process, where the system continues measuring the coupled power during the process of coupling and
welding of coupling components in their holder to each other and to the main substrate. It has been found that double ball
lenses coupling scheme is efficient and more effective for mode matching of highly elliptical (large divergence ratio) laser
diode mode field with the circular mode field of a single mode fiber, whereas for small divergence ratios the single ball lens
is adequate.
A laser diode transmitter packaged in a butterfly module is coupled into a single mode fiber using double small ball
lenses. The process of alignment and fixing of all the components inside the module is performed in an active alignment
procedure, where the laser diode is powered and the output power is continuously measured during the alignment process
of all coupling components to determine the optimum positions for maximum coupling efficiency and then fixed in their
holders and to the main substrate by laser welding technique using dual beam Nd:YAG laser welding. The double ball
lenses coupling scheme found to be very effective in mode matching between laser diode and single mode fiber. The
axial, lateral and angular 1dB misalignment tolerances are enhanced for the transformed laser mode field radii in both X
and Y directions. The experimentally measured coupling efficiency of the proposed coupling system was around 75%
with a relaxed working distance (separation of the coupling system from the fiber tip) in the range of (2-4mm) by
optimizing the separation between the two lenses as well as the separation between the first lens and the facet of the laser
diode. The experimental results match very well with those obtained theoretically by employing ABCD ray tracing
matrix.
Coupled 1X2 Single Mode Fiber (SMF-28e®) is successfully fabricated using a slightly unstable torch flame at a
temperature range 800°C to 1350°C by injecting hydrogen gas flowing at pressure of 1 bar. The fiber structure and
geometry are investigated for both core and cladding before and after fusion. Coupled fiber is studied using Field
Emission Scanning Electron Microscopy (FESEM) and Electron Dispersive X-Ray (EDX) System. The pulling length
speed, coupling time, coupling coefficient and evolution of coupling ratio from 1% until 75% are examined to study the
heating effects at the coupling region. The result shows that the core and cladding geometry of fiber are reduced 80-92%.
Their structures are changed which are shown by the changes in the refractive indices. These phenomena have wide
applications in industrial communications and sensors such as for optical switching and tunable filtering.
Coupled fibers are successfully fabricated by injecting hydrogen flow at 1bar and fused slightly by unstable torch flame in the range of 800-1350°C. Optical parameters may vary significantly over wide range physical properties. Coupling coefficient and refractive index are estimated from the experimental result of the coupling ratio distribution from 1% to 75%. The change of structural and geometrical fiber affects the normalized frequency (V) even for single mode fibers. Coupling ratio as a function of coupling coefficient and separation of fiber axis changes with respect to V at coupling region. V is derived from radius, wavelength and refractive index parameters. Parametric variations are performed on the left and right hand side of the coupling region. At the center of the coupling region V is assumed constant. A partial power is modeled and derived using V, normalized lateral phase constant (u), and normalized lateral attenuation constant, (w) through the second kind of modified Bessel function of the l order, which obeys the normal mode, LP01 and normalized propagation constant (b). Total power is maintained constant in order to comply with the energy conservation law. The power is integrated through V, u and w over the pulling length range of 7500-9500 μm for 1-D where radial and angle directions are ignored. The core radius of fiber significantly affects V and power partially at coupling region rather than wavelength and refractive index of core and cladding. This model has power phenomena in transmission and reflection for industrial application of coupled fibers.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.