|
1.IntroductionFrequency-tunable and frequency-stable microwave sources are becoming increasingly important in the fields of measurement/spectroscopy and communications. Microwave signals are usually generated using complicated electronic circuits with multistep frequency multiplication to obtain the desired frequency signal. In contrast to the complicated conventional electronic method, optical generation of microwave signals using optical beat-note generation, i.e., optical heterodyning using two optical sources, with ultrafast photodetectors (PDs)1 can be performed with simple experimental apparatuses. However, since the frequency of the generated microwave signal directly corresponds to the frequency difference between the two optical sources, frequency fluctuation may arise if the optical sources are unstable. To generate stable microwave signals, the beat-note frequency of the two optical sources used for optical heterodyning must be stabilized. Optical phase-locked loop (OPLL) is a widely used method for beat-note frequency stabilization. In OPLL, the target signal frequency is locked to a stable reference frequency generated by a radio frequency (RF) synthesizer. Using this technique, two independent lasers can be offset locked in atomic spectroscopy.2–6 The OPLL is also used in ion optical clocks7,8 for quantum information processing, power combination of high-power lasers,9 and microwave photonics.10–13 In previous studies, several other techniques have been used to obtain highly stable and low-phase noise beat notes such as two-mode optical cavity atomic resonances14 and injection locking schemes.8 The frequency stabilities of these systems are less than 1 Hz for the best performance, when the stable frequency reference (e.g., ultralow expansion glass optical cavity and ultrastable oscillator) is used. However, these systems require complicated circuits and/or special optical devices as required in OPLL and the locking range is narrow. The typical locking range of these systems is several megahertz. Recently, technological developments in electronics have enabled simple frequency stabilization schemes in high-frequency regions suitable for photonic microwave generation.15,16 Recently developed circuits can generate microwaves at 810 MHz using a simple technique; however, they have not yet been used to generate a beat note in the gigahertz frequency region. In this paper, we propose and demonstrate the photonic generation of stabilized microwave frequency signals ranging from 3 to 11 GHz using a loop filter with a delayed RF interferometer. The locking characteristics of the loop filter can be optimized with the help of the interferometer. As a result, compared with the previously reported systems, the frequency locking range of our system extends to several hundred megahertz, while a simpler operation is achieved in the proposed configuration. The frequency stability obtained in our system is higher than 1 MHz, which is sufficient for photonic RF signal generation (e.g., phased array antenna using photonic-generated RF signals1) or basic spectroscopic applications. Further improvement of frequency stability, i.e., higher than 10-kHz range stability, will be possible by using a narrow linewidth laser instead of the distributed-feedback laser used in our system. 2.PrincipleA schematic for beat-note frequency stabilization is shown in Fig. 1. The purpose of this experiment is to demonstrate the stabilization of the beat note generated by two lasers (LD1 and LD2) to generate a highly stable synthesizer signal. An RF self-heterodyne interferometer is introduced to control the locking characteristics of the servo loop. An error signal proportional to the frequency difference between the beat- and RF synthesizer-signals is converted to a DC signal and applied to LD2 to control its frequency. The RF signal intensity, , generated by PD, is proportional to the intensity of the incident light and can be expressed as where and are the amplitudes of the electric fields of the two beams of light with frequencies and , respectively. By eliminating the DC components in Eq. (1), an RF signal component from the PD, , can be obtained asSince the second term in Eq. (2) represents the higher frequency component and is outside the PD bandwidth, the component cannot be detected by the PD. Thus, only the low-frequency component [i.e., Eq. (3)] can be observed. In the following discussion, is expressed as and corresponds to the beat-note frequency. To stabilize the beat-note frequency to a reference frequency of the synthesizer, the synthesizer signal with frequency is multiplied by the beat signal using a frequency mixer. As a consequence of the multiplication, oscillating signals with two frequency components are generated, as indicated in Eq. (4). Because the frequency component is higher than the cut-off frequency of Mixer1, we can use the last term [Eq. (5)], which is proportional to , to obtain an error signal The signal proportional to is transformed into a DC signal for frequency stabilization used in the feedback loop. This is done by splitting the signal with frequency into two equal components and multiplying them by Mixer2 (bandwidth: 200 MHz), while one signal passes through an additional delay line. A coaxial cable is used as a delay line to create a delay time (5 ns for a 1-m cable) between the two signals. The delay time is equivalent to a phase shift of . The output signal from Mixer2 is Equation (6) consists of a DC part proportional to the phase shift and an AC part, which can be filtered out by a low pass filter (LPF). As a result, the error signal is obtained as By scanning the frequency of LD1 or LD2 (i.e., changing ), the error signal traces a cosine curve with a finite width corresponding to the bandwidth of Mixer2. The error signal has several zero crossing points, and one of these points is used as a locking point. The neighboring locking points are separated by . By changing the cable length of the delay line, the locking points and the slope at the zero crossing points can be changed. The locking bandwidth is given by approximately , so a shorter delay line gives a wider locking bandwidth and lower discrimination gain (i.e., derivative of the error signal at the zero crossing point), and vice versa. 3.ExperimentThe experimental setup of the photonic generation of an RF signal in the gigahertz region is shown in Fig. 2. An external cavity diode laser (ECL) and a distributed feedback (DFB) laser are used as optical sources to create an optical beat note. The ECL (Photonetics: TUNICS-PRI, linewidth: 0.5 MHz) is used for coarse tuning of the beat-note frequency, since its tuning range is wide (approximately 16 THz, corresponding to 1470 to 1599 nm). The DFB (Fitel: FRL15DCWx-A8x-W1510, linewidth: 3.3 MHz) laser is used for fine tuning of the beat frequency, together with the servo system, since its optical frequency can be controlled by an injection current. The optical output signals of the ECL and the DFB laser are combined by a 3-dB coupler. One of the output optical signals from the coupler is measured by an optical spectrum analyzer (Advantest, U3772). The beat note (the other output signal from the coupler) is detected by a fast (typically 40-GHz) photodiode (Picometrix, P-40HPA) and converted to an RF signal. The RF signal is amplified by RF amplifiers (Avantec, APT10566 and Anritsu, A3HB3102) to the range between and . The amplified signal is subsequently divided by a power splitter (Anritsu, K241C). One of the divided signals is measured by an RF spectrum analyzer or a sampling oscilloscope, while the other is mixed with the output of an RF synthesizer (Anritsu, MS9030A+MS9703) using a frequency mixer (Mini Circuits, ZX05-153+). The bandwidth of the mixer (3 to 15 GHz) is sufficient for photonic generation in the 10-GHz range. The signal, generated by mixing the beat note and RF synthesizer output, is split by a power splitter (Anritsu, K241C). One of the split signals is delayed by a coaxial cable (Hitachi Cable, MW3.00-FF-3000; length, 3 m) and multiplied by another split signal using a mixer (Mini Circuits, ZLW-3+, bandwidth: 200 MHz). The mixed signal is then amplified and used as an error signal for a feedback system. The residual RF component created by the down conversion process is eliminated by a 5-MHz LPF placed before the amplifier. 4.ResultsFigure 3 shows the measured optical spectra of the ECL and DFB laser using an optical spectrum analyzer (Advantest, Q8384). The wavelengths of the ECL and DFB laser are 1549.18 and 1549.26 nm, respectively. Using an RF spectrum analyzer, the measured frequency of the generated beat note is obtained as 9.983 GHz, as shown in Fig. 4. The obtained beat-note frequency is consistent with the difference between the two optical frequencies of the ECL and DFB laser. When the frequency of the ECL is scanned over 1 GHz, the beat-note frequency is also swept together with the frequency of ECL. According to Eq. (7), this results in a cosine variation of the error signal. Figure 5 shows the measured results of the error signal as a function of using an oscilloscope. In the servo loop, one of the zero crossing points of the error signal is used to lock the frequency difference between the ECL and DFB laser. A proportional integral derivative servo (bandwidth: 10 kHz) is used to control the injection current of the DFB laser. When the servo loop is closed, the beat frequency spectrum becomes stable, as shown in Fig. 6. For comparison, a measured free running beat frequency spectrum is shown in Fig. 7. The drift of the beat frequency is estimated to be around 22 MHz. To investigate the effect of our stabilization method, the time-domain beat note is measured by a sampling oscilloscope. Figures 8 and 9 show the measured sampling oscilloscope traces with frequency stabilization with 2-event averaging (Fig. 8) and 100-event averaging (Fig. 9). The sampling scope was self-triggered by a beat-note RF signal. In each figure, three traces are measured at 60-s intervals, three times. As shown in these figures, the three traces almost overlap, which is clear evidence that a stable beat signal has been successfully generated in our system. From these figures and the RF spectrum shown in Fig. 6, it can be concluded that the frequency noise of the beat note is reduced to almost the same level as the frequency noise of the RF synthesizer. The same measurements were then performed for the beat signal without frequency stabilization. Figures 10 and 11 show the measured sampling scope traces of the beat signal without frequency stabilization, corresponding to Figs. 8 and 9, respectively. Compared with a beat note which is frequency stabilized to the RF synthesizer signal, the beat note without frequency stabilization shown in Figs. 10 and 11 has drifted. This can be explained as follows. Without the frequency stabilization, the frequency of the ECL drifts, as shown in the beat-note RF spectrum (Fig. 7). In this situation, it is likely that the phase of the laser light shifts/jumps randomly over time. A simple mathematical calculation shows that the phase of the beat note is closely linked with the phase difference between the two optical sources used for the beat-note generation. Thus, when the phase of the RF beat signal changes because of the unstable optical phase of the laser light, the trigger timing may be changed for self-triggered oscilloscope measurements. This may be the reason for the drifting scope traces shown in Figs. 10 and 11. The similarity between the frequency-stabilized beat notes from 3 to 11 GHz is shown in Fig. 12, and the frequency stability at 10-GHz RF synthesizer frequency is shown in Fig. 13. Frequency fluctuations observed in these beat notes are less than 1 MHz over an average time of 20 s and are currently limited by the linewidth of the DFB laser. The frequency stability of the beat note was also measured using an RF spectrum analyzer. The long-term stability is improved by compared with the free running operation. To confirm the locking characteristics of the beat note frequency on the external RF signal, locked beat-note frequencies were measured as a function of the RF synthesizer frequency. The results, shown in Fig. 14, demonstrate that from 3.05 to 11.05 GHz, the beat-note frequency is precisely locked to the RF synthesizer frequency. 5.SummaryWe have developed and demonstrated a simple and versatile system to generate RF signals using optical beat generation. Since the frequency of the generated RF signal, which corresponds to the frequency difference between the two lasers, is locked to the stable external RF signal, it is not necessary to achieve absolute frequency locking of the lasers used in the beat-note generation. In our experiments, the beat-note frequency between the ECL and DFB laser is stabilized within the range 3 to 11 GHz using a delayed RF self-homodyne method combined with the stable reference frequency of the RF synthesizer. The beat-note frequency fluctuation is reduced to (short term) and (long term) compared with the fluctuation obtained by free running lasers. The proposed system will be applicable to stable and tunable giaghertz frequency range photonic generation of RF signals. ReferencesJ. Yao,
“Microwave photonics,”
J. Lightwave Technol., 27 314
–335
(2009). http://dx.doi.org/10.1109/JLT.2008.2009551 JLTEDG 0733-8724 Google Scholar
T. J. KaneA. C. NilssonR. L. Byer,
“Frequency stability and offset locking of a laser diode-pumped Nd:YAG monolithic nonplanar ring oscillator,”
Opt. Lett., 12 175
(1987). http://dx.doi.org/10.1364/OL.12.000175 OPLEDP 0146-9592 Google Scholar
T. DayE. GustafsonR. Byer,
“Sub-hertz relative frequency stabilization of two-diode laser-pumped Nd:YAG lasers locked to a Fabry-Perot interferometer,”
IEEE J. Quantum Electron., 28 1106
–1117
(1992). http://dx.doi.org/10.1109/3.135234 IEJQA7 0018-9197 Google Scholar
L. Gianfraniet al.,
“Offset-frequency locking of extended-cavity diode lasers for precision spectroscopy of water at ,”
Opt. Express, 18 21851
–21860
(2010). http://dx.doi.org/10.1364/OE.18.021851 OPEXFF 1094-4087 Google Scholar
P. Bouyeret al.,
“Microwave signal generation with optical injection locking,”
Opt. Lett., 21 1502
–1504
(1996). http://dx.doi.org/10.1364/OL.21.001502 OPLEDP 0146-9592 Google Scholar
G. Santarelliet al.,
“Heterodyne optical phase-locking of extended-cavity semiconductor lasers at 9 GHz,”
Opt. Commun., 104 339
–344
(1994). http://dx.doi.org/10.1016/0030-4018(94)90567-3 OPCOB8 0030-4018 Google Scholar
B. KeitchN. ThomasD. Lucas,
“Injection locking of violet laser diodes with a 3.2 GHz offset frequency for driving Raman transitions in 43 Ca+,”
Opt. Lett., 38
(6), 4
–7
(2013). http://dx.doi.org/10.1364/OL.38.000830 OPLEDP 0146-9592 Google Scholar
K. Komoriet al.,
“Injection-locking of blue laser diodes and its application to the laser cooling of neutral ytterbium atoms,”
Jpn. J. Appl. Phys., 42 5059
–5062
(2003). http://dx.doi.org/10.1143/JJAP.42.5059 JJAPA5 0021-4922 Google Scholar
W. Lianget al.,
“Coherent power combination of two master-oscillator-power-amplifier (MOPA) semiconductor lasers using optical phase lock loops,”
Opt. Express, 15
(6), 3201
(2007). http://dx.doi.org/10.1364/OE.15.003201 OPEXFF 1094-4087 Google Scholar
U. Glieseet al.,
“A wideband heterodyne optical phase-locked loop for generation of 3–18 GHz microwave carriers,”
IEEE Photonics Technol. Lett., 4 936
–938
(1992). http://dx.doi.org/10.1109/68.149915 IPTLEL 1041-1135 Google Scholar
J. Biesheuvelet al.,
“Widely tunable laser frequency offset lock with 30 GHz range and 5 THz offset,”
Opt. Express, 21
(12), 21
–27
(2013). http://dx.doi.org/10.1364/OE.21.014008 OPEXFF 1094-4087 Google Scholar
S. Matsuuraet al.,
“A tunable cavity-locked diode laser source for terahertz photomixing,”
IEEE Trans. Microwave Theory Tech., 48 380
–387
(2000). http://dx.doi.org/10.1109/22.826836 IETMAB 0018-9480 Google Scholar
T. Ueharaet al.,
“Frequency stabilization of two orthogonally polarized external cavity laser diodes using a novel-type optical configuration consist of a phase modulator and a Faraday rotator mirror,”
IEICE Electron. Express, 11
(10), 20140169
(2014). http://dx.doi.org/10.1587/elex.11.20140169 1349-2543 Google Scholar
A. DinovitserM. W. HamiltonR. A. Vincent,
“Stabilized master laser system for differential absorption lidar,”
Appl. Opt., 49 3274
–3281
(2010). http://dx.doi.org/10.1364/AO.49.003274 APOPAI 0003-6935 Google Scholar
U. SchünemannH. Engler,
“Simple scheme for tunable frequency offset locking of two lasers,”
Rev. Sci. Instrum., 70
(1), 242
–243
(1999). http://dx.doi.org/10.1063/1.1149573 RSINAK 0034-6748 Google Scholar
G. Rittet al.,
“Laser frequency offset locking using a side of filter technique,”
Appl. Phys. B, 79 363
–365
(2004). http://dx.doi.org/10.1007/s00340-004-1559-6 APBOEM 0946-2171 Google Scholar
BiographyTomoyuki Uehara is a research associate at the National Defense Academy of Japan. He received his BS and MS degrees in engineering from Niigata University in 2006 and 2008, respectively, and withdrew from the doctoral program with the completion of course requirements from Kyoto University, Japan. His current research interests include frequency stabilization of lasers. He is a member of SPIE. Kenichiro Tsuji received his BE, ME, and PhD degrees in engineering from Niigata University, Niigata, Japan, in 1994, 1996, and 1999, respectively. In 1999, he joined the Department of Communications Engineering, National Defense Academy of Japan, where he is currently an associate professor. His current research interests are photonic generation of coded RF signal and fiber-optic sensors based on Brillouin scattering. He is a member of OSA and IEICE. Kohei Hagiwara is a master’s course student of the National Defense Academy of Japan. He received his BS degree in engineering from the University of Electronic Communication in 2005. The same year, he joined the Japan Maritime Self Defense Force and engaged in duties of procurement, repair, and update for communication apparatus and electronics. He is a student member of IEICE and the Lieutenant Junior Grade. Noriaki Onodera received his PhD degree from Tohoku University, Sendai, Japan, in 1985. He joined the Department of Communications Engineering, National Defense Academy of Japan in 2001 is and currently a professor. His current research interests include optical generation of microwave signal and its applications. He is a member of the Institute of Electronics, Information and Communication Engineers of Japan, the Japan Society of Applied Physics, the IEEE Photonics Society and Optical Society of America. |