This work reports results of laser beam profile measurements, performed for earlier on designed and successfully fabricated silica few-mode microstructured optical fiber (MOF) with hollow-GeO2-doped-ring core (HRC). We compared two drawn from the same preform HRC MOF samples without and with induced during the drawing process twisting of 790 revolutions per meter. Researched silica HRC MOF with outer diameter 65 µm contains hollow ring-core inner diameter of 30.5 µm with wall thickness of 1.7 µm and refractive index difference Δn = 0.03; 90 air holes, placed over typical hexagonal geometry in the periphery domain from the outside HRC at the distance 14 µm, with hole averaged diameter 2.5 µm and pitch 7.5 µm. According to simulation results (mode analysis, performed by rigorous finite element method via commercially available software COMSOL Multiphysics®), it supports two guided LP-modes (fundamental LP01 and the first higher-order LP11) or 4 HE/EH odd and even eigenmodes – HE11/EH11 and HE21/EH21, respectively. We present some results of laser beam profile measurements, performed under various launching conditions (different laser sources as well as excited optical fibers (both commercially available single-mode optical fiber of ITU-T Rec. G.652 and multimode optical fiber 50/125 of ISO/IEC Cat. OM2+/OM3)) at the output ends of researched HRC MOF twisted and untwisted samples as well as at the output end of large core multimode optical fiber 100/125, aligned with excited HRC MOF.
This work reports comparative results of mode analysis, performed for earlier on designed silica microstructured optical fiber with ideal equiangular spiral six-ray geometry (ESSR-MOF) and for its real fabricated sample, differing from the model by weak asymmetry and deformed air holes. We discuss issues of input data preparation to specify analyzed complicated non-ideal fiber optic structure for computation by using rigorous finite-element method. Some results of the comparison between mode field patterns as well as guided mode effective refractive index spectral characteristics are represented. It is demonstrated, that potential deviations from the desired MOF geometry, occurring due to features of silica MOF fabrication technological process, should be taken into account during the design to predict real values of mode parameters for manufactured MOF.
This work presents results of test series, performed for earlier on designed and successfully fabricated silica few-mode microstructured optical fibers (MOF) with six GeO2-doped cores, induced twisting 100 and 600 revolutions per meter, typical “telecommunication” outer diameter 125 µm, core diameter 8.7 µm, air hole diameter 4.6 µm, pitch 7.2 µm, and core graded refractive index profiles with height 0.0275. While Part I introduced results of differential mode delay map measurements with laser source excitation / laser-based data transmission over multimode optical fibers (MMFs) with core diameters 50 and 100 µm, combined with 6-core MOF, and Part II was concerned with researches of spectral responses, measured for fiber Bragg gratings, recorded in these MOFs, Part III reports results of far-field white light beam profile measurements, performed for weakly and strong twisted 6-core-MOFs.
This work reports results of dispersion analysis, performed for the fundamental mode of silica microstructured optical fiber (MOF) with six GeO2-doped cores. We used commercially available software COMSOL Multiphysics® 6.1 with rigorous full vectorial finite element method, while earlier on fabricated and presented MOF with six step-index GeO2- doped cores end face photo image was applied to get averaged parameters for input data. Therefore, modeled multi-core MOF has typical “telecommunication” outer diameter 125 µm, it contains six cores with diameter 9.0 µm and step refractive index profile with height n=0.0275, 121 air holes with diameter 5.0 µm and pitch 7.8 µm. In this work we present results of the fundamental mode 1st…3rd order dispersion parameters, computed over all ratified “telecommunication” wavelength bands.
This work presents results of mode analysis and dispersion spectral characteristic computation, performed for recently presented successfully fabricated silica few-mode microstructured optical fiber (MOF) with hollow-GeO2-doped-ring core (HRC). Here, we utilized manufactured HRC MOF end face photo image to get averaged parameters for input data. Therefore, following simplified model HRC MOF was simulated and researched: it has outer diameter 67 µm; inner diameter of hollow ring-core is 10 µm, wall thickness 4 µm and refractive index difference Δn = 0.030 (percent of GeO2 dopant is about 20.5 mol%); 90 air holes, placed over typical hexagonal geometry in the periphery region with averaged diameter 1.85 µm and pitch 3.9 µm. According to simulation results (mode analysis, performed by rigorous finite element method via commercially available software COMSOL Multiphysics® 6.1), modeled HRC MOF provides two guided LP-modes (fundamental LP01 and the first higher-order LP11) or 4 HE/EH odd and even eigenmodes – HE11/EH11 and HE21/EH21, respectively: therefore, two orbital angular momentum (OAM) modes (OAM11 and OAM21) are localized and supported by the researched and simulated HRC MOF design. In this work we present results of spectral characteristics, computed for mode effective refractive indexes as well as for mode group delays and chromatic dispersion parameters, calculated both for eigen and OAM modes.
Earlier on we introduced model of piece-wise regular fiber optic link, operating in a few-mode regime: laser-based data transmission over large core optical fiber. Presented model is based on piecewise regular representation with general approach of split-step method application. It allows to take into account laser-excited optical signal launching conditions, differential mode delay, differential mode attenuation, higher-order mode chromatic dispersion and mode mixing / power diffusion, occurring due to optical fiber irregularity and fiber optic cable bends / twisting / stress / tension. While optical fiber irregularity can be directly set by protocols of optical fiber outer diameter monitoring system of drawing tower, cable external mechanical influences are simulated via equivalent angular misalignment at the splices of regular spans. Therefore, this work is concerned with issues of selection of this equivalent angular misalignment (EAM). We performed a computational test series under various values of mentioned above EAM under following comparison with experimentally measurements of few-mode optical pulse responses at the output of multimode optical fibers with strong differential mode delay effect.
This work presents results of test series, performed for earlier on designed and successfully fabricated silica few-mode microstructured optical fibers (MOF) with six GeO2-doped cores, induced twisting 100 revolutions per meter, typical “telecommunication” outer diameter 125 μm, core diameter 8.7 μm, air hole diameter 4.6 μm, pitch 7.2 μm, and core quasi-step / graded refractive index profiles with height 0.0360/0.0275, respectively. Part I introduces attempts for splicing of typical telecommunication optical fibers and fabricated samples of MOFs by commercially available field arc fusion splicer kits and results of differential mode delay map measurements, performed for laser excited large core (multimode) optical fibers with core diameters 50 and 100 μm, jointed via free space to described above 2 m long pilot samples of 6-GeO2-core MOFs at both receiving and transmitting ends under laser-excited gaussian optical pulse launching with precision offset conditions, while Part II is concerned with researches of spectral responses, measured for fiber Bragg gratings, recorded in these MOFs.
This study aimed to investigate the potential application of distributed fiber-optic acoustic sensors for speech recognition amidst complex audio backgrounds. The experimental measurements were carried out on the mock-up room with a fiberoptic link. The possibility of application the fiber-optic distributed acoustic sensor for localization of sound source and recognition of musical and human speech signals amidst complex audio backgrounds was demonstrated. The signal detected by DAS provides good quality of music composition recognition and clear speech recognition. The difference in spectrum of signals detected by microphone and DAS was analyzed. The signal noise ratios were calculated for test speech signal with different average levels and its influence on the speech recognition was analyzed.
This work presents results of test series, performed for earlier on designed and successfully fabricated twisted silica fewmode microstructured optical fibers (MOF) with six GeO2-doped cores. While Part I introduces results of differential mode delay map measurements, Part II is focused on researches of spectral responses, measured for fiber Bragg gratings, recorded in these multi-core MOFs with core graded refractive index profiles and induced twisting 100 revolutions per meter. Specially setup for spectral response measurement for described complicated fiber optic element was developed, that provides selected alignment of matching singlemode optical fiber with particular single core of MOF via free space and reducing of reflection by precision 8 angle cleaving. Comparing analysis of measured spectral responses confirmed written FBGs in 2 of 6 cores, and demonstrated potentiality of fabricated complicated structure, containing multi-core MOF with FBG, for applications in multichannel fiber optic sensors with spatial division multiplexing technique.
This work presents some results of pulse and spectral responses, performed for laser-excited pilot sample of earlier on designed and fabricated chiral silica few-mode optical fiber (FMF) with induced twisting 66 revolutions per meter (rpm), typical (for telecommunication optical fibers) cladding diameter 125 μm, weakly increased core diameter up to 11 μm and numerical aperture NA=0.22, corresponding to improved height of quasi-step refractive index profile. Described FMF 11/125 provides propagation of 4 and 6 guided modes over “C” and “O”-bands, respectively. We present results of tests, focused on researches of few-mode effects, occurring under laser-excited optical signal propagation over pilot sample optical fiber, and their influence on pulse and spectral responses, including some measurements, performed for fiber Bragg grating, recorded in tested FMF 11/125.
This work reports the results of bandwidth measurements and tests, performed for earlier on designed and fabricated pilot lengths of new silica laser-optimized graded-index multimode fibers (LOMFs) with extremely enlarged core diameter up to 100 μm and "typical" "telecommunication" cladding diameter 125 μm. Presented optical fibers are targeted for harsh environment short-range multi-Gigabit onboard cable systems and industrial networks. Proposed LOMF 100/125 differs by specially optimized graded refractive index profile, that provides low differential mode delay (DMD) for selected guided modes. We present some results of tests, performed for fabricated pilot 520 m length of described LOMF 100/125, focused on researches of bandwidth features. They contain DMD map and transfer function measurement as well as 10GBase-LX/SX channels eye-diagram and bit-error-ratio reports with following direct detection of the maximal acceptable optical fiber length for guaranteed 10Gbps channel supporting.
The methods for estimation of optical fiber curvature distribution based on reflectometric measurement on two wavelength and using polarization reflectometry were proposed. The method for estimation of correction coefficients for bend-insensitive optical fibers for was represented. The approbation of methods on test setup of a fiber-optic communication line including segments with different bending radii was performed.
This work is concerned with some aspects of selection of graded refractive index profiles for couple combination of optical crypto-fibers “encryptor”–“decryptor”. We present some results of experimental approbation of method for differential mode delay (DMD) management by selection and recombination of two corresponding refractive index profiles, differing by technological defects in the core center. Here it is supposed, that combined fiber optic link, containing the sequence of two graded-index multimode optical fibers with strong DMD, occurring due to great technological defect of refractive index profile in the core center with a peak (or dip) in the first and, on the contrary, with a dip (or peak) in the second, provide inverting DMD diagram of selected mode components in the second optical fiber in relation to the first. Therefore, according to earlier on proposed alternative method for implementation of secure data transmission channel protected over physical layer for the "first/last mile" segment of intra-corporate network, the first optical fiber with strong unique distortions is considered as “encryptor”, while the second with inverted DMD diagram implements function of “decryptor” in the optical interface.
Following article presents a simple scheme of an acousto-optic channel and an example of the results of modeling lowspeed data transmission in such channel. Previously obtained experimental data on the amplitude-frequency response of the channel were used in the simulation. The simulation results demonstrate the advantage of using a phase receiver for the considered fiber acousto-optic channels compared to direct detection.
This work presents some results of experimental approbation of method for writing of cascaded precision microstructured defects, like "tapers" and "up-tapers", in various configurations and sequences in silica multimode graded index optical fibers by commercially available field fusion splicer with modified software settings. Here we utilized earlier on developed technique for micro-defect geometry parameters estimation via analysis of photo-image, performed after defect writing and displayed on fusion splicer screen, to estimate the least available distance between couples of the “up-tapers” and “tapers” without optical fiber structure deformation. Also, some results of insertion loss measurements for various configuration of 3-element cascaded microstrucured defects are presented.
This work is concerned with experimental research of laser beam profile dependence on micro-lensed optical fiber configuration. We considered prepared lensed and tapered cone optical fiber samples and tested them on developed experimental setup to analyze laser beam profile from the output of the lensed optical fiber end. Some comparison results of detected spatial distribution patterns of laser source emission from the end of cleaved and lensed optical fiber ends are presented.
This work is concerned with development of simple method for making of alternative fiber optic Raman probe components containing silica optical fibers with formed precision micro-lens under desired configuration and geometry parameters at the fiber end face by commercially available field fusion splicer kit and its modified software settings. We present methods for writing both hemispherical lenses and ball lenses as well as tapered cones, results of their experimental approbation and results of following carried out experimental research of fusion splicer software settings impact on microlensed optical fiber geometry parameters – radius and length.
This work is concerned with research of Haar wavelet threshold sensitivity for detection of non-reflective events corresponding to optical fiber fusion splices on fragments of fiber optic link traces measured by optical time domain reflectometer (OTDR). We performed test series contained 40 step-by-step repeatable splicing of the same couple of standard singlemode fibers of ITU-T Rec. G.652 spools with length 2.2 km and 4.2 km and outer termination by conventional singlemode FC/UPC pigtails for OTDR connection and following bidirectional trace measurement. Results of insertion loss estimation and accomplished by OTDR software automated detection of non-reflective event corresponding to fusion splice of described optical fibers as well as ability of its visual manual localization on trace were recorded. The first 30 splices were realized by fusion splicer conventional program for jointing standard singlemode optical fibers of ITU-T Rec. ITU-T G.652, while the next 10 splices were done under “attenuator” mode with preset increased insertion loss. Described link traces were measured by OTDR operating in a standard mode with high spatial resolution under pulse width 20 ns and appropriate dynamic range with far-end OSNR 6.5 dB at wavelength 1550 nm. As a result 80 traces were analyzed in both automated and manual modes with fusion splice insertion loss varied from 0.002 dB to 0.554 dB. At the next stage we applied continues Haar wavelet transform for detection non-reflective event on measured traces of lab fiber optic link containing described one fusion splice with total length about 6.4 km. According to results, wavelet transform of described link trace provides detection of extremely low loss non-reflective events with OTDR reading down to own error corresponding to 0.020…0.030 dB range under improved scaling over normalized spatial diagram of wavelet coefficients.
We present alternative method for implementation of secure data transmission channel protected over physical layer for the "first/last mile" segment of intra-corporate network by specialized fiber optic link. Proposed solution is based on application of operating in a few-mode laser-based regime multimode optical fibers with special refractive index profile providing optical pulse strong uniquely distortions due to differential mode delay effect that allows to consider those optical fibers as "encryptor". Therefore, transmitted traffic is strongly distorted and it is unable to be processed without corresponding "decryptor" which might be either also another one optical fiber with "inversed" refractive index profile in relation to the "encryptor"-fiber or electronic dispersion compensator device modified for such application. This work is concerned with configurations of proposed "crypto" fiber optic link as well as brief description of math apparatus for design it. Some results of preliminary simulations are also represented.
This work presents results of experimental approbation of earlier on proposed modified fiber optic stress sensor based on a few-mode effects occurring during laser-excited optical signal propagation over silica multimode optical fiber (MMF). Modification is concerned with a passage to quasi-interferometric scheme realized by two multimode Y-couplers with equalized arm lengths improved by fiber Bragg grating (FBG) written on preliminary formed precision macrostructure defects in silica multimode graded-index optical fibers and special offset launching conditions providing laser-based excitation of higher-order modes. The “arms” of quasi-interferometer are two equalized lengths of MMF Cat. OM2 with great central dip of refractive index profile and strong pulse splitting due to high differential mode delay (DMD). We tested FBGs with Bragg wavelength both 1310 nm and 1550 nm written over tapers or up-tapers preliminary formed in short pieces of MMF Cat. OM2+/OM3 and further jointed to the end of one of the arms before output Y-coupler. Researches were focused on comparison analysis of pulse responses under changing of selected excited mode mixing and power diffusion processes due to stress distributed action to sensor fiber depending. Here we considered FBGs not only as particular wavelength reflector during spectral response measurement but also as local periodic microstructure defect which strongly effects on few-mode signal components mixing process also improved by combination with macro-defect like taper or up-taper that should provide response variation. Some results pulse response measurements produced for different scheme configuration and their comparison analysis are represented.
This work presents method for performing precision macro-structure defects “tapers” and “up-tapers” written in conventional silica telecommunication multimode optical fibers by commercially available field fusion splicer with modified software settings and following writing fiber Bragg gratings over or near them. We developed technique for macrodefect geometry parameters estimation via analysis of photo-image performed after defect writing and displayed on fusion splicer screen. Some research results of defect geometry dependence on fusion current and fusion time values re-set in splicer program are represented that provided ability to choose their “the best” combination. Also experimental statistical researches concerned with “taper” and “up-taper” diameter stability as well as their insertion loss values during their writing under fixed corrected splicer program parameters were performed. We developed technique for FBG writing over or near macro-structure defect. Some results of spectral response measurements produced for short-length samples of multimode optical fiber with fiber Bragg gratings written over and near macro-defects prepared by using proposed technique are presented.
We present method for design of refractive index profile for silica GeO2-doped graded-index few-mode optical fibers with reduced differential mode delay and suppressed mode nonlinearity due to extremely enlarged core diameter up to 42 μm. Proposed solution is based on earlier on developed modified Gaussian approximation generalized for analysis of silica weakly guiding optical fibers with single outer cladding and arbitrary axially-symmetric refractive index profile, that provides ability to derive analytical expressions for guided mode delays. Therefore the objective function is represented as a sum of squares of deviations between mode staff delays and reference value corresponding to refractive index profile of current iteration. Based on developed method we performed computation for various combination of the reference mode delay and first iteration profile parameter. Some results of desired graded-index profile for a few-mode optical fibers 42/125 providing differential mode delay minimization over central region of "C"-band are represented.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.