Three-dimensional (3D) perovskite photodetectors (PPDs) demonstrate remarkable photoelectric detection ability, but the intrinsic instability of 3D perovskite films against moisture, oxygen, and temperature has been a roadblock for achieving great stability and reliability of the resulting PDs, which can be mainly ascribed to the inevitable defects on surfaces and grain boundaries that can incur nonradiative charge recombination to impair device performance and initiate the degradation of perovskites. In this work, we introduced the two-dimensional (2D) perovskite material PEAI to fabricate a high-performance and stable 2D/3D stacked PPD. As a result, the responsivity of the PEAI processed PPD (PEAI-PPD) reached 1.19 A/W under the illumination of 532 nm laser with the power density of 5 μW/cm2 at bias voltage of −1 V, and retains 80.15% of the initial value after 16 days of nonencapsulated storage at 10%-15% relative humidity (RH). Our work provides a simple and effective method for the fabrication of high-performance and stable 2D/3D stacked PPDs, which has great application potential in visible light communication, imaging and environmental monitoring under complex environmental conditions.
Publisher’s Note: This paper, originally published on 27 February 2019, was replaced with a corrected/revised version on 16 November 2021. If you downloaded the original PDF but are unable to access the revision, please contact SPIE Digital Library Customer Service for assistance.
Chiral metasurfaces can realize strong chiral optical responses and various spin-dependent electromagnetic manipulations. In this paper, we propose a metal-graphene hybrid metasurface that achieves active control of the amplitude and wavefront of reflected circularly polarized terahertz wave. By introducing a single layer graphene at the bottom of the patterned metasurface, combined with the silicon layer for voltage control, continuous change of the circular dichroism (CD) from 0 to 0.6 is obtained. Then we realized dynamic switching of the terahertz beam from anomalous reflection to vertical reflection using Pancharatnam-Berry (P-B) phase. This tunable chiral metasurface provides new ideas for the design of terahertz devices.
Organic-inorganic metal halide perovskite material is an emerging semiconductor material that is widely used in functional devices such as solar cells and photodetectors. It has many advantages, low preparation cost, high light absorption coefficient, long carrier diffusion length, high carrier mobility, etc. However, due to the instability of perovskite, it is easy to decompose in the water and oxygen environment, which has become an obstacle to its development. In this paper, by adding polymethyl methacrylate to the anti-solvent to reduce the perovskite grain boundaries, improve directional growth and the quality of the film. The performance of the photodetector prepared by this method has been effectively improved, there is a significant photocurrent under illumination, and the stability has also been improved. This method provides a good candidate for the next generation of high-performance photodetectors.
Organic field-effect transistor (OFET) photonic memories have attracted significant attention due to their special memory mechanism and potential application, such as image capture and light information storage. Conventional OFET memories based on SiO2 blocking dielectric layer usually need a high programming and erasing voltage, which is not conducive to the needs for future market applications. Here, the low-voltage OFET photonic memory is investigated by using spin-coated organic polymer as the blocking dielectric layer and blending film of CsPbBr3 quantum dots (QDs) and polystyrene (PS) as the charge trapping layer, respectively. The thin poly(methyl methacrylate) (PMMA) film is used as the first blocking dielectric layer, and the ultrathin polyvinyl alcohol (PVA) film is used as secondary blocking dielectric layer on the top of PMMA. Due to the use of thin polymer blocking dielectric layers, the operating voltages of the photonic memory can be as low as 5 V. And the photo-generated carriers can be effectively trapped and released in photosensitive charge trapping layer during the photo-programming and electrical erasing operations. In addition, the memory characteristics of the photonic memory are comparable to that of traditional memories with SiO2 blocking dielectric layer. Multi-level data storage can be obtained in the memory by applying different photo-programming conditions. The low-voltage OFET memory device also presents well retention and endurance. Hence, the low-voltage OFET photonic memory using solution-processed polymer blocking dielectric and photosensitive charge trapping layer shows great potential for the application in optoelectronic devices in terms of large-area and low cost.
Infrared photodetectors (IRPDs) are of importance devices with wide applications from face identification to space communication. With the investigation of thermoelectric materials, perovskite and three-dimensional (3D) graphene have been demonstrated and fabricated to thermoelectric PDs with response to terahertz bands separately. Herein, we develop thermoelectric PD based on 3D graphene and perovskite hybrid material with good IR performance. The responsivity at 1 V bias reaches to 0.1 A/W, under the illumination of 1064 nm laser with the power density of 3.1 mW, corresponding noise equivalent power (NEP) 1 nW∙Hz-1/2 , the rise time 10.8 ms and fall time 12.8 ms, respectively. These results demonstrate these hybrid IRPDs show good IR performance, and can provide a reference for other spectral range such as terahertz bands.
The preparation of high-quality perovskite films with optimal morphologies is important for achieving high-performance perovskite photodetectors (PPDs). An effective strategy to optimize the morphologies is to add antisolvents during the spin-coating steps. In this work, an environment-friendly antisolvent ethyl acetate (EA) was employed to improve the quality of perovskite films, which can effectively regulate the formation of an intermediate phase staged in between a liquid precursor phase and a solid perovskite phase due to its moderate polarity, and further promote the homogeneous nucleation and crystal growth in the subsequent annealing process, thus leading to the formation of high-quality perovskite films and enhanced photodetector (PD) performance. As a result, the responsivity of the PPDs reached 0.85 A W-1 under the illumination of 532 nm laser with the power density of 6.37 μW cm-2 at bias voltage of -2 V. The corresponding detectivity reached 3.27 × 1011 Jones, while the rise time and fall time are 256 ns and 370 ns, respectively. These results demonstrates that our developed solution-processed method with EA as antisolvent has remarkably advantages for the fabrication of high-performance PPDs and can provide a reference for the other similar research work.
Terahertz (THz) waves are electromagnetic waves with frequencies between 0.1 THz and 10THz. With the rapid development of wireless communication, the existing spectrum resources have become increasingly scarce. Developing the new frequency band of wireless communication has gradually become a consensus to solve this contradiction. There are a lot of unexploited resources in THz frequency range, making terahertz play a decisive role in the future development of wireless communication. Three-dimensional (3D) graphene with connection carbon nanomaterials is expected to possess better optical and electrical properties than single-layer graphene. In this paper, we studied a room temperature ultra-broadband photodetector based on 3D graphene and investigated the different photoresponse at 0.22, 2.52, 30 THz. Obvious photocurrents and ultra-broadband absorption from infrared spectrum to terahertz (THz) region can be measure in the three 3D graphene. A high photoresponsivity of 15.3 mA W-1 and a fast time response of 20 ms have been achieved at 2.52 THz. The results reveal 3D graphene a good candidate for room-temperature broadband Terahertz detector.
Graphene is a hot material for photodetectors due to its high carrier mobility, superior electronic and optical properties. However, the low optical absorption (2.3%) of graphene results in a low photoresponsivity, which limits its wide application in photodetection field. Three-dimensional (3D) graphene with connection carbon nanomaterials is expected to possess better optical and electrical properties than single-layer graphene. In this paper, we studied an ultra-broadband photodetector based on 3D graphene and investigated the different photoresponse with three kinds of 3D graphene including the 3D reduced oxide graphene foam (rGOF), the 3D Nickel (Ni) skeleton graphene foam (GF) and the 3D removal of nickel graphene foam (RNi GF). Obvious photocurrents and ultra-broadband absorption from ultraviolet (UV) spectrum to terahertz (THz) region can be measure in the three 3D GF. A high photoresponsivity of 50 mA W-1 and a fast time response of 100 ms have been achieved. Particularly, the 3D RNi GF presents the highest absorption coefficient of 200 cm-1 at THz region. The results reveal 3D graphene a good candidate for broadband photodetectors.
All-inorganic perovskite quantum dots (QDs) have widely used in a lot of micro-nano photoelectric devices. However, resistive random access memory (RRAM) devices based on All-inorganic perovskite QDs are relatively scarce. In this work, a RRAM, which exhibits the write-once-read-many-times (WORM) memory effect, based on CsPbBr3 QDs was successfully fabricated by solution processed method at room temperature. The CsPbBr3 QDs based memory shows great reproducibility, good data retention ability, irreversible electrical transition from the high resistance state (HRS) or OFF state to the low resistance state (LRS) or ON state and the resistance ratio (ON/OFF) can reach almost 107. To study the CsPbBr3 QDs based WORM memory provides an opportunity to develop the next generation high-performance and stable WORM devices.
Methylammonium lead halide perovskites have received substantial attention in photoelectric research communities, because of excellent optoelectronic properties, including long electron-hole diffusion distance, large absorption coefficients in the UV–Vis spectral region, low-cost, solution-based processing and low binding energy of exciton. Many records, such as efficiencies have been kept by these perovskite solar cells. However, other excellent properties, such as ultrafast properties have not been studies intensively. Here vertical field effect phototransistors (VFEpTs) based on methylammonium lead halide perovskites were design and fabricated. VFEpTs exhibit high performances including an ultrafast photoresponse time (less than 20 ns) and a high photoresponsivity (~ 10 mAW−1). The methylammonium lead halide perovskite vertical phototransistors open path on ultrafast devices with low cost solution fabrication process, but high level performances.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.